Announcements
New Discussions
Previous Thread
Next Thread
Print Thread
Rating: 5
Hop To
H14 forestay to long! Need new bow tang? #27962
01/21/04 01:00 AM
01/21/04 01:00 AM
Joined: Jan 2004
Posts: 4
Oregon
Capt_Morse Offline OP
stranger
Capt_Morse  Offline OP
stranger

Joined: Jan 2004
Posts: 4
Oregon
I have a near stock 1970 Hobie 14. I recently purchased new forestays, shrouds, bridles and other related hardware. My old cable fit just fine, I was able to adjust the rake on the mast as I think it should be able to adjust. When I got my new cables, I set up my mast and in order to keep all the cables tight I had to set all the adjusters to the tightest settings. The cables are tight enough on the lowest settings but this leaves me with no adjustment capability.

I was looking through the parts diagrams in the Hobie catalog and saw the bow tang in the catalog was different than the one I have on my boat. My bow tang has 4 screws into the fiberglass, 2 on each side of a loop, much like the Eye Strap (part 2072 on page 39 of the 2003 catalog) only with 4 screws not 2. The bow tang in the parts diagram is a loop with one screw. The bow tang on my boat is mounted about 4 inches from the tip of the bow. I think the new bow tang bolts through the lip at the very tip of the bow. Is this true? How hard would it be to change the bow tang? Would this solve the problem of my to long cables? What do I need to do to change the bow tang? Do I need to reinforce the lip on the bow with some resin? Is there any thing else I need to know?

Thanks
Capt. Morse

-- Have You Seen This? --
Re: H14 forestay to long! Need new bow tang? [Re: Capt_Morse] #27963
01/31/04 02:34 PM
01/31/04 02:34 PM
Joined: Jan 2004
Posts: 6
Nebraska
BubbaH16 Offline
stranger
BubbaH16  Offline
stranger

Joined: Jan 2004
Posts: 6
Nebraska
What are the mearsurements of the new wires? How about the old? I am getting ready to replace mine and would like to know what else you have found out about the bow tang. My H14 is set-up the same way as yours.

Thanks

Re: H14 forestay to long! Need new bow tang? [Re: BubbaH16] #27964
02/02/04 11:32 AM
02/02/04 11:32 AM
Joined: Jan 2004
Posts: 152
Central Texas
yoh Offline
member
yoh  Offline
member

Joined: Jan 2004
Posts: 152
Central Texas
This might be a bit off topic (What I am writing here may or may not be valid for a H14)...
On the Hobie 16 new (replacement) shrouds are about 8 cm longer than those that were originally installed on my mid 80's hobie 16. I assume that at the same time the effective lenght of the forestay was increased. IIRC these changes were made to allow to rake the mast further back. May be you have to get forestay and shrouds in a "combo".

Patrick


Patrick, Hobie 16 '85
Re: H14 forestay to long! Need new bow tang? [Re: yoh] #27965
02/02/04 06:50 PM
02/02/04 06:50 PM
Joined: Jul 2001
Posts: 744
Bob_Curry Offline
old hand
Bob_Curry  Offline
old hand

Joined: Jul 2001
Posts: 744
If you order your new wires from Murrays, ask them to make them to "Bob Curry's latest wire lengths". You will have the right lengths.

Be Happy!!

Bob


"The election is over, the talking is done, Your party lost, my party won. So let us be friends, let arguments pass, I’ll hug my elephant, you kiss you’re a $$.”
Liberalism = A brain eating amoeba & a failed political ideology of the 20th century!
Re: H14 forestay to long! Need new bow tang? [Re: Capt_Morse] #27966
02/24/04 11:49 AM
02/24/04 11:49 AM
Joined: Jan 2004
Posts: 4
Oregon
Capt_Morse Offline OP
stranger
Capt_Morse  Offline OP
stranger

Joined: Jan 2004
Posts: 4
Oregon
Thanks every one for the input, but no one has answered my question. How is the bow tang mounted to the newer Hobie 14's? Is it with a screw into the fiberglass or is it with a bolt thru the lip at the very tip of the bow, just like the 16?

Thanks
Capt. Morse

Re: H14 forestay to long! Need new bow tang? [Re: Capt_Morse] #27967
02/24/04 01:25 PM
02/24/04 01:25 PM
Joined: Jul 2001
Posts: 744
Bob_Curry Offline
old hand
Bob_Curry  Offline
old hand

Joined: Jul 2001
Posts: 744
There is a nut fiberglassed into the hull. The tang bolt threads in to it. There is not enough lip up front to bolt thru like the 16. Also, it's not strong enough!!

Bob


"The election is over, the talking is done, Your party lost, my party won. So let us be friends, let arguments pass, I’ll hug my elephant, you kiss you’re a $$.”
Liberalism = A brain eating amoeba & a failed political ideology of the 20th century!
Re: H14 forestay to long! Need new bow tang? [Re: Bob_Curry] #27968
02/24/04 05:55 PM
02/24/04 05:55 PM
Joined: Jun 2001
Posts: 1,252
California
mmiller Offline
veteran
mmiller  Offline
veteran

Joined: Jun 2001
Posts: 1,252
California
The "Nut" is actually a small square plate of aluminum about 1/4" thick. The old tang was 4 bolts drilled and tapped into the corners of the plate. The new tang is one larger (same as a 16 tang and bolt) drilled and tapped in the center of the same plate.


Hobie Cat Forums
Matt Miller
Hobie Cat Company
Re: H14 forestay to long! Need new bow tang? [Re: mmiller] #27969
02/25/04 09:58 PM
02/25/04 09:58 PM
Joined: Sep 2003
Posts: 84
ms/fl
fuzzy Offline
journeyman
fuzzy  Offline
journeyman

Joined: Sep 2003
Posts: 84
ms/fl
well, its probably a good idea to measure what ya got and verify what you will be getting.tr


A-class #19

Moderated by  Damon Linkous 

Search

Who's Online Now
0 registered members (), 399 guests, and 86 spiders.
Key: Admin, Global Mod, Mod
Newest Members
Darryl, zorro, CraigJ, PaulEddo2, AUS180
8150 Registered Users
Top Posters(30 Days)
Forum Statistics
Forums26
Topics22,404
Posts267,055
Members8,150
Most Online2,167
Dec 19th, 2022
--Advertisement--
Powered by UBB.threads™ PHP Forum Software 7.7.1