Announcements
New Discussions
Previous Thread
Next Thread
Print Thread
Rate Thread
Hop To
Page 1 of 2 1 2
what are daggers and rudders generally made of? #125832
12/07/07 06:37 PM
12/07/07 06:37 PM
Joined: Sep 2007
Posts: 757
japan
erice Offline OP
old hand
erice  Offline OP
old hand

Joined: Sep 2007
Posts: 757
japan
hi all,
am idly thinking of sometime in the future reshaping the daggers and rudders on my old nacra 5.2 to a more modern profile, (round out the forward lower corner of the daggers and removing some of the width of the rudder blades)

but to do so i need to know what they cored with
heavy enough to either be ply or solid glass!

or maybe safer to copy them in shaped ply and then wrap with glass, anyone guess what weight of cloth and how many layers would be needed to provide enough strength?


eric e
1982 nacra 5.2 - 2158
2009 weta tri - 294
-- Have You Seen This? --
Re: what are daggers and rudders generally made of [Re: erice] #125833
12/07/07 07:03 PM
12/07/07 07:03 PM
Joined: Nov 2003
Posts: 749
Santa Cruz, CA
SurfCityRacing Offline
old hand
SurfCityRacing  Offline
old hand

Joined: Nov 2003
Posts: 749
Santa Cruz, CA
Most are foam core with glass or carbon skin. Oftentimes, the builder will use some sort of stringer for stiffness. The H Tigers have 3 G10 stringers running the length. The old 18's didn't have stringers. They are usually built in two halves and glued together.
Not sure about the 5.2.

Re: what are daggers and rudders generally made of [Re: SurfCityRacing] #125834
12/08/07 03:15 AM
12/08/07 03:15 AM
Joined: May 2003
Posts: 4,451
West coast of Norway
Rolf_Nilsen Offline
Carpal Tunnel
Rolf_Nilsen  Offline
Carpal Tunnel

Joined: May 2003
Posts: 4,451
West coast of Norway
G10 stringers??

Re: what are daggers and rudders generally made of [Re: SurfCityRacing] #125835
12/08/07 05:39 AM
12/08/07 05:39 AM
Joined: Sep 2007
Posts: 571
Hamburg
Smiths_Cat Offline
addict
Smiths_Cat  Offline
addict

Joined: Sep 2007
Posts: 571
Hamburg
Hi SurfCity and all,

Old tornados used wooden rudders. Is there any true reason, why todays rudders are from class or CFRP? The rudders of my Dart are of glass and heavy, and I see no point that wooden rudders could not resist the loads acting on it. Having a straight leading edge, a aluminium or glass or kevlar leading edge cover would be easly applicable.

Cheers,

Kolja

Re: what are daggers and rudders generally made of [Re: Smiths_Cat] #125836
12/08/07 07:37 AM
12/08/07 07:37 AM
Joined: Feb 2005
Posts: 4,118
Northfield Mn
Karl_Brogger Offline
Carpal Tunnel
Karl_Brogger  Offline
Carpal Tunnel

Joined: Feb 2005
Posts: 4,118
Northfield Mn
One off would be expesive, but a set of polished aluminum blades and rudders would look super cool. Or worse yet in the finance department what about titanium?

Re: what are daggers and rudders generally made of [Re: erice] #125837
12/08/07 10:18 AM
12/08/07 10:18 AM
Joined: Jun 2001
Posts: 12,310
South Carolina
Jake Offline
Carpal Tunnel
Jake  Offline
Carpal Tunnel

Joined: Jun 2001
Posts: 12,310
South Carolina
Those boards are fiberglass with a sort of solid resin core. I'm not certain exactly what they use in the core on those but you can sand to it, shape it, and cover it a little with some glass with no problem.


Jake Kohl
Re: what are daggers and rudders generally made of [Re: Karl_Brogger] #125838
12/08/07 10:36 AM
12/08/07 10:36 AM
Joined: Jun 2006
Posts: 121
Hollister CA, Plano TX
A
avalondarlyn Offline
member
avalondarlyn  Offline
member
A

Joined: Jun 2006
Posts: 121
Hollister CA, Plano TX
I built a set of rudders and daggers for a viva 27. The rudders were 1 3/4 in thick, by I think 38 long and were very heavy solid mahogany. I used the originals as cores planed them down about 3/8 3/16 from each side and then cut off the leading and trailing edge leaving a top w/ a tapered stringer. I then glued on 1 lb styren foam. A few templates and and using my old surfboard shaping skills. 1 layer of of uni-knitted "rutan" glass "highly recommened" about 2/3 lenth and then 1 layer of 4oz glass. a little micro light. the new rudders were approx 48 in long an extra 8 in. with the last 12 in or so just, an egg shell. skin. new rudders were about 1/3 the wieght. With an much improved foil. I used a naca 12 foil. If I did it again I use the resource "here" to get a better foil. As for daggers, I used www.flyingfoam.com had Bob cut the cores with a cnc machine. again glassed w/ approx 10 layers of the Rutan uni-knitted glass. 1 layer of 4 oz glass. a little micro light. new boards were great I got close to a naca 12 foil but was restricted by the slot. new daggers were 8 ft 4 in long. and wieghed about 30 lbs each about 50 lbs lighter than the originals. In my opinion, the wieght savings vs strenth vs cost I would look at the new cloths being developed by the airplane composite company's. The foils I built were with in 10-15% of the wieght of a full carbon foil. But approx 1/3 the price. These are my opinons based upon 20+ years "part time" of fiberglass and water craft production and airplane restoration. PM if you want or need an opinion. Question has anybody out there built a set of aluminum boards I'm considering it for my new project "C-class" if so I would like to see how they were built.

Re: what are daggers and rudders generally made of [Re: avalondarlyn] #125839
12/08/07 12:06 PM
12/08/07 12:06 PM

A
Anonymous
Unregistered
Anonymous
Unregistered
A



Guy at the Texas city dike where I use to sail had a SWEET set of wooden rudders on his Hobie 21. Even LONG spin run of hours her had no problem. Light tan and dark mahogany color. They looked REALLY good.

Doug

Re: what are daggers and rudders generally made of [Re: ] #125840
12/08/07 02:11 PM
12/08/07 02:11 PM
Joined: Nov 2003
Posts: 749
Santa Cruz, CA
SurfCityRacing Offline
old hand
SurfCityRacing  Offline
old hand

Joined: Nov 2003
Posts: 749
Santa Cruz, CA
They don't have to be high tech. I've heard that there was a company that made wooden rudders for the H14 and 16 back in the day. Anyone know about that?

I don't know anything about this really, but my friends at Elkhorn Composites were building hollow surfboards out of aluminum honeycomb core and carbon. They were super stiff and very light. I thought it would be a cool way to make rudders. It would be expensive though! Billet aluminum on a CNC would be cool Karl. Titanium??? Ouch, my wallet.<img src="http://www.catsailor.com/forums/images/graemlins/cool.gif" alt="" />



You can make daggers out of a lot of materials and each method has pluses and minuses.


[Linked Image]

Re: what are daggers and rudders generally made of [Re: SurfCityRacing] #125841
12/08/07 06:59 PM
12/08/07 06:59 PM
Joined: Feb 2005
Posts: 4,118
Northfield Mn
Karl_Brogger Offline
Carpal Tunnel
Karl_Brogger  Offline
Carpal Tunnel

Joined: Feb 2005
Posts: 4,118
Northfield Mn
When I used to race quads you could buy a steel axle for about $400, the Ti ones were close to a thousand. Just a reference. Aluminum would be plenty strong and light. Plus you can polish it to a mirror shine. I wonder what it would actually cost? Might be cheaper than one would think.

Re: what are daggers and rudders generally made of [Re: Karl_Brogger] #125842
12/09/07 05:46 AM
12/09/07 05:46 AM
Joined: Sep 2007
Posts: 757
japan
erice Offline OP
old hand
erice  Offline OP
old hand

Joined: Sep 2007
Posts: 757
japan
weighed my daggers today and they came in at 5kg or 11lb each, which must be much heavier than newer foam cored daggers

i think solid alloy would weigh about the same, however an aerospace alloy honeycomb core, like the old usa ski maker hexcel used, wrapped and sealed in riveted duralinium skins would be pretty cool

pity i'm no longer working as an aircraft mechanic with access to all that cool stuff



well shaped ply would look pretty good too as the different colored laminates would show up like contour lines in the leading and trailing edge tapers

maybe if they are well soaked in resin they wouldn't even need a cloth sheath. doing without the cloth would make them easier to build and lighter

might cut out some bits and start flex comparisons, i know the glass ones can support my weight after my last 2 capsizes and that old nacra daggers can break when being used all the way down in heavy air. perhaps they aren't flexible enough


eric e
1982 nacra 5.2 - 2158
2009 weta tri - 294
Re: what are daggers and rudders generally made of [Re: erice] #125843
12/09/07 03:12 PM
12/09/07 03:12 PM
Joined: Oct 2006
Posts: 902
Norman,OK
gree2056 Offline
old hand
gree2056  Offline
old hand

Joined: Oct 2006
Posts: 902
Norman,OK
Flexible is bad when you are trying to go fast.


Once you go cat you never go back! Nacra 5.2 (Elsies)#1499, running an inter17 spin!
Re: what are daggers and rudders generally made of [Re: gree2056] #125844
12/09/07 04:22 PM
12/09/07 04:22 PM
Joined: Sep 2007
Posts: 757
japan
erice Offline OP
old hand
erice  Offline OP
old hand

Joined: Sep 2007
Posts: 757
japan
lateral twists in the dagger cases would be bad but if others are snapping 5.2 boards in heavy air it seems to me they don't give enough

those long high aspect daggers on boats like the inter17 and A cats at half the width and twice the length must bend more than 5.2 boards

if 2 daggers weigh 10kg, 22lbs, together, then the 2 rudder blades probably weigh another 5kg, 11lbs. that's 10% of the boats 150kg, 325lbs


eric e
1982 nacra 5.2 - 2158
2009 weta tri - 294
Re: what are daggers and rudders generally made of [Re: Karl_Brogger] #125845
12/10/07 11:50 PM
12/10/07 11:50 PM
Joined: Jul 2001
Posts: 953
Western Australia
Stewart Offline
old hand
Stewart  Offline
old hand

Joined: Jul 2001
Posts: 953
Western Australia
I have seen "ally" skinned plates and rudders for a serious contender for Cherub skiff class....

They had a backbone stringer made of wood and the plate ally was folded. The backbone then formed the max depth. The issue is sealing the trailing edge and keeping the plate ends at the trailing edge together. They solves it by riveting the two edges and silicon sealing. It worked.. At that stage one couldnt weld easily thin plate end to plate end. The other issue is the temp to weld would warp the plate near to the trailing edge and thus create uneven flow.. High speed and uneaven flow isnt much fun..
I dont think much was gained over a conventional plate.

Re: what are daggers and rudders generally made of [Re: Stewart] #125846
12/10/07 11:55 PM
12/10/07 11:55 PM
Joined: Feb 2005
Posts: 4,118
Northfield Mn
Karl_Brogger Offline
Carpal Tunnel
Karl_Brogger  Offline
Carpal Tunnel

Joined: Feb 2005
Posts: 4,118
Northfield Mn
I think you would have to do it billet. Cut it from one piece of aluminum. I'm sure there are places you could ship a rudder to and they would be able to scan it and be able to make a 3D CAD image for a cnc

Re: what are daggers and rudders generally made of [Re: erice] #125847
12/11/07 12:08 AM
12/11/07 12:08 AM
Joined: Jul 2001
Posts: 953
Western Australia
Stewart Offline
old hand
Stewart  Offline
old hand

Joined: Jul 2001
Posts: 953
Western Australia
if your asking me..
I would get access to a cnc machine.
Then laminate up alternative strips of foam and wood (western red cedar or similar) alternatively balsa strips with carbon running between each strip and a central strip of western red.. I have used both techniques. Here I will say having a semi-dense wood core, like western red, at the tips and edges helps when impact happens! So the blank profile is 2 cm of western red 10cm light foam 10 cm western red 10 light foam 2 cm wester red. For a total width of 340 mm. One can use smaller and more strips if one wishes but try and keep the max width with the denser core as well as the tip being totally dense core.

Then glassing skins to the cnc form. Glass or carbon as your mech engineer requires to handle the loads.

I would not use a foam only form unless your really sure of the skin thickness!! Even then the point loading when righting the boat or sailing under hard conditions can be very interesting!!

hope that helps




<img src="http://www.catsailor.com/forums/images/graemlins/grin.gif" alt="" />

Re: what are daggers and rudders generally made of [Re: erice] #125848
12/12/07 12:46 AM
12/12/07 12:46 AM
Joined: Oct 2002
Posts: 307
maui
jollyrodgers Offline
enthusiast
jollyrodgers  Offline
enthusiast

Joined: Oct 2002
Posts: 307
maui
doubtful that you should take a grinder to your foils.
wood is a perfectly good material to make new ones. you will need to glass them. they need to be quite strong so stringers are great. put one at max camber for easy shaping.

foils for the foilboards are cut from aluminum billet on a cnc. some big windsurf fins are made that way. heavy and accurate. g10 on a cnc is a good way to make a windsurf fin. heavy, accurate, expensive, right amount of flex for a board.
when H16 first came out we were forced into making rudders because the abs ruuders couldn't handel the loads.it was a while before lexan rudders were invented, so a whole market sprang up to supply usable rudders. the molded ones were glass with mysterious fillers, and the custom ones were wood. there was lead in the wood blades because rudders had to be 7 or 10 pounds(whatever the rule is). i always thought my wood ones were a speed advantage. the best tornado blades were custom wood with glass in those days.

Re: what are daggers and rudders generally made of [Re: jollyrodgers] #125849
12/12/07 02:12 AM
12/12/07 02:12 AM
Joined: May 2003
Posts: 4,451
West coast of Norway
Rolf_Nilsen Offline
Carpal Tunnel
Rolf_Nilsen  Offline
Carpal Tunnel

Joined: May 2003
Posts: 4,451
West coast of Norway
The Tornado class dont allow carbon in the foils, so the best rudders around are still wood. Not hand shaped, but veneers put into a mould and laminated. I have tried finding out how Marstrøm do this, but no success so far.

What is g10? Some kind of alu?

Re: what are daggers and rudders generally made of [Re: Karl_Brogger] #125850
12/12/07 10:42 AM
12/12/07 10:42 AM
Joined: Jul 2001
Posts: 953
Western Australia
Stewart Offline
old hand
Stewart  Offline
old hand

Joined: Jul 2001
Posts: 953
Western Australia
I would probably not go down the path of cnc'ing a block of "ally"..
While it sounds great "ally" does not float!! So if for some reason it comes out of the case the whole thing sinks!! At least with wood you have a chance the plate/rudder can be retrieved.
Even though its old read the chapter in Frank Bethwaite's book.

For those classes which have a no carbon rule.. Very thin veneer or ultrathin ply is the natural carbon substitute.. One can steam veneer and epoxy together to make a side of plate.. then put in the backbone stringer epoxy the side together and glass.. should be very strong and light

Last edited by Stewart; 12/12/07 11:13 AM.
Re: what are daggers and rudders generally made of [Re: erice] #125851
12/12/07 11:15 AM
12/12/07 11:15 AM
Joined: Jan 2006
Posts: 39
Richmond Virginia
NACRADUDE Offline
newbie
NACRADUDE  Offline
newbie

Joined: Jan 2006
Posts: 39
Richmond Virginia
Quote
might cut out some bits and start flex comparisons, i know the glass ones can support my weight after my last 2 capsizes and that old nacra daggers can break when being used all the way down in heavy air. perhaps they aren't flexible enough


Had a friend of mine snap two 5.2 boards in heavy air quite recently with two big guys on the wire in 30+. When you experience that type of wind it is better to raise the boards about 1/3 of the way to help depower the boat along with droping the traveler. Without a reef point that's a good way to reduce the chance of inadvertant swimming.


Money can't buy you love, but it can rent it for a while
Page 1 of 2 1 2

Moderated by  Damon Linkous 

Search

Who's Online Now
0 registered members (), 637 guests, and 78 spiders.
Key: Admin, Global Mod, Mod
Newest Members
Darryl, zorro, CraigJ, PaulEddo2, AUS180
8150 Registered Users
Top Posters(30 Days)
Forum Statistics
Forums26
Topics22,404
Posts267,055
Members8,150
Most Online2,167
Dec 19th, 2022
--Advertisement--
Powered by UBB.threads™ PHP Forum Software 7.7.1