New Discussions
36th America's Cup
by mikekrantz. 03/18/18 01:19 PM
Worrell 1000 Reunion Race
by Worrell1000RR. 03/17/18 06:59 AM
2018 Florida 300 - Register Now!
by cyberspeed. 03/13/18 01:29 AM
Adding a Jib to a Mossie
by Greg/Debra. 03/05/18 04:48 AM
New Nacra Infusion MKIII - Epoxy F18
by samc99us. 02/28/18 12:10 PM
ISO a Hobie 16 mast somewhat near SW Montana
by yellowstonehobie. 02/22/18 05:33 PM
Portsmouth or SCHRS ???
by Jake. 02/22/18 11:30 AM
2018 Sarasota OD Midwinters
by samc99us. 02/20/18 12:46 PM
Indeed Timbo, where did everyone go?
by northsea junkie. 02/20/18 01:33 AM
MIami OCR - 2020 Olympics
by brucat. 02/17/18 08:56 AM
Previous Thread
Next Thread
Print Thread
Rate Thread
Hop To
Creaking hulls... again! #281383
12/15/15 04:41 AM
12/15/15 04:41 AM
Joined: Aug 2011
Posts: 179
Grafton, NSW
Greg/Debra Offline OP
Greg/Debra  Offline OP
Joined: Aug 2011
Posts: 179
Grafton, NSW
We have previously had problems with creaking hulls/ beam on our Carter plywood boat 1434, which have been somewhat solved by tightening the beam bolts on bigger washers.

But now our Boyer boat 1727 has started creaking, and it is getting worse. It is the rear beam on the port hull which is making the noise. I have checked the bolts, but they are tight to turn. (Maybe they could be glued?)

Does anyone have any experience with creaking hulls on Boyer boats?

1140 Gadfly
1434 J.I.B.E.
1727 Atreus
-- Have You Seen This? --
Re: Creaking hulls... again! [Re: Greg/Debra] #281393
12/15/15 10:40 AM
12/15/15 10:40 AM
Joined: Oct 2010
Posts: 92
South Oz
Phillip Offline
Phillip  Offline
Joined: Oct 2010
Posts: 92
South Oz
Hi Greg, Check the frame/bulkhead under the rear beam is 'tight'. Access through the deck inspection hole and push the frame all around it where it bonds to the hull and deck. It may not be seen to be loose but listen for the creaking sound your refer to. We had one in SA with a loose main beam frame. And yes it creaked during sailing and when pushed. The movement between hull and frame edge could also be felt as well as heard. Repair in this case required cutting the deck forward of the beam to rejoin frame to the hull side. If this is your problem, hopefully access for repair can be made through the rear deck's inspection port. FYI, my creaking sound was the side stay tangs (when luffed up and no sailing pressures). I replaced the round head screws with countersunk head. Now no movement and subsequent creaking. Had the same problem with the transom rudder fittings 1765 so new what to do with the tangs. Oh, also set them in araldite. Good luck with your search!

Tortured ply is clearly beautiful.
Mozzie Aldebaran VI

Moderated by  Damon Linkous 


Who's Online Now
1 registered members (Mark Schneider), 27 guests, and 356 spiders.
Key: Admin, Global Mod, Mod
Newest Members
ortegakid, windhorze, NickA, xxrb1, Silverhorse47
7758 Registered Users
Top Posters(30 Days)
brucat 4
Jake 4
Timbo 3
Forum Statistics
Most Online554
May 12th, 2017
Powered by UBB.threads™ PHP Forum Software
(Release build 20180111)
Page Time: 0.005s Queries: 15 (0.002s) Memory: 0.9253 MB (Peak: 1.0373 MB) Zlib enabled. Server Time: 2018-03-18 21:33:50 UTC