Announcements
New Discussions
New England 100 2018
by brucat. 07/21/18 10:29 PM
do you carry one of these?
by brucat. 07/21/18 08:59 PM
F16 Effect Crew Weight Solo and 2 Up
by samc99us. 07/20/18 01:12 PM
CL258 and CL259 Clamcleats for Trap Harness
by samc99us. 07/20/18 01:11 PM
Aussie Nacra Nationals 2018-2019
by JeffS. 07/20/18 04:27 AM
What happened?
by Gato. 07/18/18 09:46 AM
W22 Trimaran
by Gato. 07/17/18 02:17 PM
Recreational A-Cat
by mmadge. 07/13/18 06:40 AM
Where did everyone go?
by DennisMe. 07/10/18 09:48 AM
Help locating Center Boards
by TexasTuma. 07/05/18 04:28 PM
Boyer hull moulds have to go
by 11Damo70. 07/01/18 07:33 PM
Hobie Getaway rudder assmbly problem
by David Parker. 06/25/18 04:08 PM
Great Lakes long distance event Around PEC
by pitchpoledave. 06/24/18 06:43 PM
Previous Thread
Next Thread
Print Thread
Rate Thread
Hop To
Hobie 16 Mast step link #273526
06/28/14 12:01 PM
06/28/14 12:01 PM
Joined: Jun 2014
Posts: 1
P
phatdad Offline OP
stranger
phatdad  Offline OP
stranger
P
Joined: Jun 2014
Posts: 1
Hello Guys and Gals. My first post. Been sailing for 30 years.
My first Beach cat. I bough an older Hobie 16. Picked up a mast step link kit, but not sure about using it. You have to remove the hook on the mast step. Should I just leave it be our install the kit. Any picks would be helpful.
Thanks for your time.

-- Have You Seen This? --
Re: Hobie 16 Mast step link [Re: phatdad] #273599
06/30/14 08:39 PM
06/30/14 08:39 PM
Joined: Jun 2001
Posts: 493
Minnesota
Jeff Peterson Offline
addict
Jeff Peterson  Offline
addict
Joined: Jun 2001
Posts: 493
Minnesota
I'm confused by what you mean by "hook on mast step". Is something already attached to the holes in either the mast bottom, or the base that receives the mast?



Jeff Peterson
H-16 Sail #23721
Big Marine Lake, MN
Re: Hobie 16 Mast step link [Re: phatdad] #273611
07/01/14 06:44 AM
07/01/14 06:44 AM
Joined: Jul 2001
Posts: 206
Virginia USA
CMerrell Offline
enthusiast
CMerrell  Offline
enthusiast
Joined: Jul 2001
Posts: 206
Virginia USA
[img]http://www.onlinemarinestore.com/store/pc/viewPrd.asp?idproduct=15015&idcategory=0[/img]

The narrow fork of the hinge goes in the slot in the mast step, secure with a pin through the holes. The wider fork goes around the tang on the mast base, secure with a pin through the LOWER set of holes. Place a teflon chip in the mast step cup. Stand on the tramp near the stern and raise the mast. The bottom of the mast may need to be shoved back and down to seat in the cup. Secure the forestay to the bridle. Many sailors use a double 10-hole chainplate at the bridle to make it a little easier.

Hope this helps.

Re: Hobie 16 Mast step link [Re: Jeff Peterson] #273612
07/01/14 06:47 AM
07/01/14 06:47 AM
Joined: Jan 2004
Posts: 1,884
Detroit, MI
mbounds Offline
Pooh-Bah
mbounds  Offline
Pooh-Bah
Joined: Jan 2004
Posts: 1,884
Detroit, MI
Originally Posted by Jeff Peterson
I'm confused by what you mean by "hook on mast step". Is something already attached to the holes in either the mast bottom, or the base that receives the mast?

The original Hobie 16 mast base had a hook that engaged a pin in the mast base to help raise the mast. Only problem was that the hook had a bad tendency to disengage when the mast was about half-raised.

Hobie Cat quickly introduced the mast step link kit. Older boats could be easily retrofitted with it.

Re: Hobie 16 Mast step link [Re: phatdad] #278441
04/18/15 02:20 AM
04/18/15 02:20 AM
Joined: Apr 2015
Posts: 1
C
Collin Offline
stranger
Collin  Offline
stranger
C
Joined: Apr 2015
Posts: 1
I'm confused by what you mean by "hook on mast step". Is something already attached to the holes in either the mast bottom, or the base that receives the mast?

Re: Hobie 16 Mast step link [Re: Collin] #278493
04/21/15 11:26 AM
04/21/15 11:26 AM
Joined: Jun 2001
Posts: 1,252
California
mmiller Offline
veteran
mmiller  Offline
veteran
Joined: Jun 2001
Posts: 1,252
California
The link is pinned or bolted to the mast step casting. You align the mast base at the link and pin the link to a hole in the base casting. The two being connected by a "Hinge Link" for stepping.

Older models had a hook as part of the base and a pin in the step casting. You can drill out the pin. Cut off the hook and drill a hole in the base to update older boats.

Item #21380001 MAST STEP LINK KIT H14/16

Order from any Hobie Catamaran dealer.

[Linked Image]

Step link instructions


Hobie Cat Forums
Matt Miller
Hobie Cat Company
Re: Hobie 16 Mast step link [Re: phatdad] #280065
07/27/15 09:03 PM
07/27/15 09:03 PM
Joined: Aug 2007
Posts: 3,954
B
brucat Offline
Carpal Tunnel
brucat  Offline
Carpal Tunnel
B
Joined: Aug 2007
Posts: 3,954
I realize that this is a slightly older thread, but...

I've had one of those screws nearly shear over time. Ever since, I always replace them with a solid clevis pin before they go on the boat.

Hope this helps.

Mike


Moderated by  Damon Linkous 

Search

Who's Online Now
1 registered members (Damon Linkous), 21 guests, and 277 spiders.
Key: Admin, Global Mod, Mod
Newest Members
Mikeylikesit, Beata, PiratesCoveCat, knussy, reiser5
7809 Registered Users
Top Posters(30 Days)
brucat 8
JeffS 4
Gato 3
Beata 1
Forum Statistics
Forums26
Topics22,313
Posts266,616
Members7,809
Most Online554
May 12th, 2017
--Advertisement--
Powered by UBB.threads™ PHP Forum Software 7.6.1.1