Announcements
New Discussions
Previous Thread
Next Thread
Print Thread
Rate Thread
Hop To
TMS - update #199401
12/23/09 12:02 AM
12/23/09 12:02 AM
Joined: Feb 2009
Posts: 678
Palm Beach County
TheManShed Offline OP
addict
TheManShed  Offline OP
addict

Joined: Feb 2009
Posts: 678
Palm Beach County
Happy Holidays!

Iíve had some interest in my project that is good! My shoulder is doing better still hurts but I deal with it. The doc will not let me sail yet, someday.

Still fairing out the starboard half of the hull but getting there. I got a new account for discount parts so that will help. The first of the year Iím going LLC and changing the name to TMS Composites, a bit more professional but Iíll still be the ďThe Man ShedĒ and just alias the new name. So both names should hit the website and the website will start to change after the first of the year.

TMS-20
Iíll post of few pictures. Right now Iíve got the hull upside down. I hope that is not bad karma and spilling out the mojo. I found it easier to long board the bottom of the hull with it upside down. Iím going to get it close then when the port side is done match them up. The mold is flipped and Iíve done some faring on the mold so the next side should take less bog. Iím concerned about the weight Iíve added but it is not enough to worry about. I need to get it as fair as I can to make a mold off of it (if I have to). Iíd still rather do the CNC plug but have not found any takers yet. Iíve secured several sheets of Divinycell foam but Iím one sheet short right now. Seems to be a shortage of foam and the plant is closed until after the first of the year. Iím going to glue the strips with Gorilla Glue it is suppose to sand easier according to the ďFarrier BoysĒ.

I spoke to Kurt Hughes about Carbon connecting beams so I have a plan for the building the beams. Iím going to make a mold for the beams off of the mast section I have that should be a fun project. Iíve also decided to make a mold for the AMAís so Iíll make one plug and not have to worry about the weight. Hind site is always 20/20. Iím looking forward to 2010 and hope to launch the TMS-20 in the New Year.

Best Wishes!

Attached Files
P1010023.JPG (271 downloads)
P1010026.JPG (269 downloads)
Stations flipped, fared, and sealed
P1010027.JPG (273 downloads)
Last edited by TheManShed; 12/23/09 05:32 PM. Reason: spelling problems at 1:00Am hmmm

Mike Shappell
www.themanshed.com
TMS-20 Builder
G-Cat 5.7 - Current Boat
NACRA 5.2 - early 70's

-- Have You Seen This? --
Re: TMS - update [Re: TheManShed] #199402
12/23/09 12:03 AM
12/23/09 12:03 AM
Joined: Feb 2009
Posts: 678
Palm Beach County
TheManShed Offline OP
addict
TheManShed  Offline OP
addict

Joined: Feb 2009
Posts: 678
Palm Beach County
few more pics....

Attached Files
P1010029.JPG (272 downloads)
P1010036.JPG (271 downloads)

Mike Shappell
www.themanshed.com
TMS-20 Builder
G-Cat 5.7 - Current Boat
NACRA 5.2 - early 70's

Re: TMS - update [Re: TheManShed] #199415
12/23/09 08:42 AM
12/23/09 08:42 AM
Joined: Jun 2001
Posts: 12,310
South Carolina
Jake Offline
Carpal Tunnel
Jake  Offline
Carpal Tunnel

Joined: Jun 2001
Posts: 12,310
South Carolina
Mike,

Wouldn't it be easier to fair the exterior of the hull after it's joined with the other half and with the structural reinforcement inside? You could be fairing twist into it - no?


Jake Kohl
Re: TMS - update [Re: Jake] #199448
12/23/09 02:28 PM
12/23/09 02:28 PM
Joined: Feb 2009
Posts: 678
Palm Beach County
TheManShed Offline OP
addict
TheManShed  Offline OP
addict

Joined: Feb 2009
Posts: 678
Palm Beach County
I have several temp bulkheads in the hull and it is very stiff with the carbon and foam. Most of the fairing is with it laying flat on a table. Yes for the final fairing and I'm just about done for now until I build the other half.


Mike Shappell
www.themanshed.com
TMS-20 Builder
G-Cat 5.7 - Current Boat
NACRA 5.2 - early 70's

Re: TMS - update [Re: Jake] #199455
12/23/09 04:01 PM
12/23/09 04:01 PM
Joined: Nov 2005
Posts: 1,203
uk
TEAMVMG Offline
veteran
TEAMVMG  Offline
veteran

Joined: Nov 2005
Posts: 1,203
uk
He hasn't laminated the outer skin yet either Jake


Paul

teamvmg.weebly.com
Re: TMS - update [Re: TEAMVMG] #199466
12/23/09 05:39 PM
12/23/09 05:39 PM
Joined: Feb 2009
Posts: 678
Palm Beach County
TheManShed Offline OP
addict
TheManShed  Offline OP
addict

Joined: Feb 2009
Posts: 678
Palm Beach County
When you lift the hull either by the ends or side it does not flex. It is still light enough that my wife and I can easily lift it over our heads, even with the temp wood bulkheads and my bad shoulder. The whole key to all of the faring is that the outer skin will be thin compared to a usual lay-up of all E-glass. The outer skin will be 2 layers of 198 gram (6.9oz) carbon and one layer of 4 oz E-glass all 90 degree unidirectional cloth, except for the stress points they will have 4 layers of carbon.

This is the same lay-up inside except the stress points have 6 layers of carbon.....problem reading the plans and a little extra does not hurt. What I tried to show here is the fine entry and shape of the underwater profile, not much wetted surface. If I kept the same profile above the waterline it would have been a real skinny boat and a tight fit. I added the flare to increase the cabin space and as a result it should throw the spray to the side. The water line is about 2/3 of the way to the flare. The boat looks wider then the wetted surface profile when it is right side up. That was my main objective in the modification to the plans: More room without an increase of wetted surface.

The pics show the volume of the hull above the DWL and temp bulkheads.

Attached Files
P1110017.JPG (163 downloads)
P1110019.JPG (163 downloads)

Mike Shappell
www.themanshed.com
TMS-20 Builder
G-Cat 5.7 - Current Boat
NACRA 5.2 - early 70's

Re: TMS - update [Re: TheManShed] #199546
12/26/09 11:17 PM
12/26/09 11:17 PM
Joined: Feb 2009
Posts: 678
Palm Beach County
TheManShed Offline OP
addict
TheManShed  Offline OP
addict

Joined: Feb 2009
Posts: 678
Palm Beach County
So Craig and I are having a few holiday spirits and up walks a horse. She usually does not come in the shed but Craig is known to carry Carrots and it must have looked like we were having fun. If I can only teach her to sand.

Attached Files
DSC00016.JPG (111 downloads)
DSC00017.JPG (110 downloads)
DSC00019.JPG (110 downloads)

Mike Shappell
www.themanshed.com
TMS-20 Builder
G-Cat 5.7 - Current Boat
NACRA 5.2 - early 70's

Re: TMS - update [Re: TheManShed] #199562
12/27/09 12:04 PM
12/27/09 12:04 PM
Joined: Jan 2004
Posts: 196
Arkansas, USA
C
CaptainKirt Offline
member
CaptainKirt  Offline
member
C

Joined: Jan 2004
Posts: 196
Arkansas, USA
Actually, you can! Just spray salt or maybe carrot juice on the hull? Cows used to lick the paint off my car while I was driving a tractor in OK- supposedly to get salt/minerals?? Mebbe it only works w/ OK cows but you could try? ;-)

Kirt


Kirt Simmons
Taipan, Flyer
Re: TMS - update [Re: CaptainKirt] #199564
12/27/09 12:50 PM
12/27/09 12:50 PM
Joined: Feb 2009
Posts: 678
Palm Beach County
TheManShed Offline OP
addict
TheManShed  Offline OP
addict

Joined: Feb 2009
Posts: 678
Palm Beach County
Too funny but no cows. Just cats, dog and a horse. Promissed my wife she could have a horse if we moved in the country...it is a trade off for the boats.


Mike Shappell
www.themanshed.com
TMS-20 Builder
G-Cat 5.7 - Current Boat
NACRA 5.2 - early 70's


Moderated by  Damon Linkous 

Search

Who's Online Now
0 registered members (), 32 guests, and 210 spiders.
Key: Admin, Global Mod, Mod
Newest Members
diveboy, Carlos_Mata_Virgem, bfriendly, BlairC, Skahahobie
8093 Registered Users
Top Posters(30 Days)
Forum Statistics
Forums26
Topics22,385
Posts267,020
Members8,093
Most Online1,650
Sep 10th, 2019
--Advertisement--
Powered by UBB.threads™ PHP Forum Software 7.7.1