Announcements
New Discussions
New England 100 2018
by brucat. 07/22/18 12:41 PM
do you carry one of these?
by brucat. 07/21/18 08:59 PM
F16 Effect Crew Weight Solo and 2 Up
by samc99us. 07/20/18 01:12 PM
CL258 and CL259 Clamcleats for Trap Harness
by samc99us. 07/20/18 01:11 PM
Aussie Nacra Nationals 2018-2019
by JeffS. 07/20/18 04:27 AM
What happened?
by Gato. 07/18/18 09:46 AM
W22 Trimaran
by Gato. 07/17/18 02:17 PM
Recreational A-Cat
by mmadge. 07/13/18 06:40 AM
Where did everyone go?
by DennisMe. 07/10/18 09:48 AM
Help locating Center Boards
by TexasTuma. 07/05/18 04:28 PM
Boyer hull moulds have to go
by 11Damo70. 07/01/18 07:33 PM
Hobie Getaway rudder assmbly problem
by David Parker. 06/25/18 04:08 PM
Great Lakes long distance event Around PEC
by pitchpoledave. 06/24/18 06:43 PM
Previous Thread
Next Thread
Print Thread
Rate Thread
Hop To
Hobie 21se (non-conducting) comp tip #287928
09/26/17 01:09 PM
09/26/17 01:09 PM
Joined: Apr 2012
Posts: 190
B
Bille Offline OP
member
Bille  Offline OP
member
B
Joined: Apr 2012
Posts: 190
The comp-tip on my Hobie-21se is getting over aged from the Las Vegas
sun , and i need to do something about it now.

I can make a accurate mold of it , and build a fiberglass or Kevlar one
using epoxy ; but will the fiberglass conduct electricity, or should i stick
to using just the Kevlar and paint it white ,( kevlar does Not like sun-shine) ?

I wouldn't know how to make another plastic one ; and can't afford a
new one.

Bille

-- Have You Seen This? --
Re: Hobie 21se (non-conducting) comp tip [Re: Bille] #287929
09/26/17 06:12 PM
09/26/17 06:12 PM
Joined: Jun 2001
Posts: 12,303
South Carolina
Jake Offline
Carpal Tunnel
Jake  Offline
Carpal Tunnel
Joined: Jun 2001
Posts: 12,303
South Carolina
Fiberglass / epoxy or Fiberglass / any-ester resin will not conduct electricity. It's really only carbon filaments that you need to worry about conductivity with in composites (unless you are using some aluminum coated glass fibers...but I digress).

Fiberglass would be a lot easier to work with than kevlar (not to mention cheaper). If you want to get the good structural / stronger fiberglass, go with s-type.


Jake Kohl
Re: Hobie 21se (non-conducting) comp tip [Re: Bille] #287930
09/26/17 07:38 PM
09/26/17 07:38 PM
Joined: Jan 2004
Posts: 1,884
Detroit, MI
mbounds Offline
Pooh-Bah
mbounds  Offline
Pooh-Bah
Joined: Jan 2004
Posts: 1,884
Detroit, MI
The original is fiberglass. Only the track is plastic. Getting the tolerances right where the track attaches will be really, really hard. It's probably better to just refinish the existing one and replace the track.

Re: Hobie 21se (non-conducting) comp tip [Re: Bille] #287932
09/27/17 11:00 AM
09/27/17 11:00 AM
Joined: Apr 2012
Posts: 190
B
Bille Offline OP
member
Bille  Offline OP
member
B
Joined: Apr 2012
Posts: 190
Thanks you guys !

I already have the fiberglass , Kevlar, and epoxy to do this job ; but refinishing
the original , and getting a new track, is definitely the way to go !!

After Ya told me the original was fiberglass --- i went in and dug through
the cracked and dried-out surface layer ; low & behold , it Was made
of fiberglass .

I'll check around for a new track now, (fingers X'd) ; meanwhile i can start sanding
down the fiberglass part and put some non metallic paint on it .


Thanks again : Bille


Moderated by  Damon Linkous 

Search

Who's Online Now
1 registered members (Isotope235), 17 guests, and 201 spiders.
Key: Admin, Global Mod, Mod
Newest Members
Mikeylikesit, Beata, PiratesCoveCat, knussy, reiser5
7809 Registered Users
Top Posters(30 Days)
brucat 10
JeffS 4
Gato 3
Beata 1
Forum Statistics
Forums26
Topics22,313
Posts266,618
Members7,809
Most Online554
May 12th, 2017
--Advertisement--
Powered by UBB.threads™ PHP Forum Software 7.6.1.1